Kenmore Dryer Model 796 Not Heating!

Kenmore Dryer Model 796 not heating may be due to a faulty heating element or a blown thermal fuse. In such cases, troubleshooting the heating system components is essential to address the issue.

When a Kenmore Dryer Model 796 fails to heat, it can be frustrating. However, understanding the possible causes of this problem is crucial in order to fix it. One of the common culprits behind a non-heating dryer is a defective heating element.

This component generates the heat needed to dry clothes. Another possible cause is a blown thermal fuse, which is designed to protect the dryer from overheating. Troubleshooting the heating system elements can help identify and rectify the issue, allowing you to restore proper functionality to your Kenmore Dryer Model 796.

Credit: reviewed.usatoday.com

Possible Causes For Lack Of Heat In Kenmore Dryer 796 Model

Is your Kenmore Dryer Model 796 not heating up? You rely on your dryer to get your clothes dry and ready to wear, so it can be quite frustrating when it fails to produce any heat. There are several possible causes for this lack of heat, and in this article, we will explore three common issues that may be causing your Kenmore Dryer Model 796 to not heat up properly.

Thermal Fuse Failure

One possible cause for the lack of heat in your Kenmore Dryer Model 796 is a thermal fuse failure. The thermal fuse is a safety device that is designed to prevent the dryer from overheating. If the thermal fuse blows, it will cut off power to the heating element and cause the dryer to not produce any heat. This is a common issue that can occur if the dryer is overloaded or if there is a clog in the vent system, causing the dryer to overheat.

If you suspect that the thermal fuse is the culprit, you can use a multimeter to test it for continuity. If the thermal fuse is defective, it will need to be replaced before the dryer can produce heat again. It’s always a good idea to consult the user manual or seek professional help to ensure proper replacement.

Heating Element Malfunction

Another possible cause for the lack of heat in your Kenmore Dryer Model 796 is a malfunctioning heating element. The heating element is responsible for generating the heat needed to dry your clothes. If the heating element becomes faulty or breaks, it will not be able to produce any heat, resulting in a dryer that runs but doesn’t heat up. To determine if the heating element is the issue, you can visually inspect it for any signs of damage or wear.

If it appears to be damaged or if you are unsure, it is recommended to consult a professional technician to diagnose and replace the heating element if necessary. A faulty or broken heating element should be replaced to restore proper heat production in the dryer.

Igniter or Gas Valve Issues

The third possible cause for the lack of heat in your Kenmore Dryer Model 796 is igniter or gas valve issues. If your dryer is powered by gas, a faulty igniter or gas valve can prevent the dryer from producing heat. The igniter is responsible for igniting the gas as it flows into the burner assembly, while the gas valve controls the flow of gas. If either of these components is faulty, the dryer will not heat up.

To diagnose this issue, you can visually inspect the igniter for any signs of damage or wear. If the igniter appears to be damaged or if you are unsure, it is recommended to consult a professional technician to diagnose and replace the faulty component. A malfunctioning igniter or gas valve should be replaced to restore heat production in the dryer.

In conclusion, if you are experiencing a lack of heat in your Kenmore Dryer Model 796, there are three main possible causes to consider: thermal fuse failure, heating element malfunction, and igniter or gas valve issues.

Each of these issues requires proper diagnosis and potential replacement of faulty components. By identifying and addressing the underlying cause, you can get your dryer back up and running, delivering the heat necessary to dry your clothes efficiently.

How To Test And Replace The Thermal Fuse In Kenmore Dryer 796 Model?

If you own a Kenmore Dryer 796 model and are experiencing the frustrating issue of it not heating, one of the common culprits could be a faulty thermal fuse. The thermal fuse is a safety device that prevents the dryer from overheating. In this section, we will walk you through the steps to access, test, and replace the thermal fuse in your Kenmore Dryer 796 model.

Steps to Access the Thermal Fuse

Before you begin testing or replacing the thermal fuse, you will need to access it. Follow these steps to access the thermal fuse in your Kenmore Dryer 796 model:

1. Unplug the dryer from the power source to ensure your safety.
2. Move the dryer away from the wall to create enough space for you to work comfortably.
3. Remove the screws that secure the dryer’s back panel using a screwdriver.
4. Once the screws are removed, carefully detach the back panel from the dryer.

Testing the Thermal Fuse with a Multimeter

Now that you have accessed the thermal fuse, it’s time to test it using a multimeter. Follow these steps to test the thermal fuse in your Kenmore Dryer 796 model:

1. Set your multimeter to the ohms/continuity setting.
2. Locate the thermal fuse, which is usually situated near the heating element or blower housing.
3. Remove the wires connected to the thermal fuse by gently pulling them off.
4. Place one multimeter lead on each terminal of the thermal fuse.
5. If the multimeter reading shows “continuity” or near-zero resistance, the thermal fuse is functional. However, if the reading shows “no continuity” or infinite resistance, the thermal fuse is faulty and needs to be replaced.

Removing and Replacing the Thermal Fuse if Necessary

If the test results indicate that the thermal fuse is faulty, you will need to remove and replace it. Follow these steps to remove and replace the thermal fuse in your Kenmore Dryer 796 model:

1. Disconnect the wires from the faulty thermal fuse.
2. Using a screwdriver, remove the screws that secure the thermal fuse in place.
3. Carefully remove the faulty thermal fuse from its housing.
4. Take the new thermal fuse and insert it into the housing, ensuring it aligns correctly.
5. Tighten the screws to secure the new thermal fuse in place.
6. Reconnect the wires to the appropriate terminals of the new thermal fuse.

Once you have completed these steps and successfully replaced the thermal fuse, you can reattach the dryer’s back panel, plug it back into the power source, and test your Kenmore Dryer 796 model to check if it resolves the heating issue. Remember to always prioritize safety and consult a professional if you are unsure of any steps or encounter further issues.

How To Diagnose And Fix A Faulty Heating Element In Kenmore Dryer 796 Model?

When your Kenmore Dryer Model 796 is not heating, a faulty heating element could be the culprit. The heating element is responsible for generating the necessary heat to dry your clothes. If it is not working correctly, your dryer may not heat up as it should, resulting in damp clothes even after a full cycle. However, diagnosing and fixing a faulty heating element is not as difficult as it may seem.

Step-by-step guide to accessing the heating element

Before you can test or replace the heating element in your Kenmore Dryer Model 796, you need to access it. Here’s a step-by-step guide to help you with this process:

1. Unplug your dryer or turn off its power source
2. Remove the lint filter from the top of the dryer
3. Using a screwdriver, remove the screws that hold the lint trap housing in place
4. Slide a putty knife between the top panel and the front panel to release the clips securing them together
5. Lift the top panel and prop it up against the wall
6. Disconnect the door switch wire harness from the front panel
7. Remove the screws that secure the front panel to the sides of the dryer
8. Carefully lift and remove the front panel
9. Locate the heating element on the right side of the dryer

Testing the heating element for continuity using a multimeter

To determine if the heating element in your Kenmore Dryer Model 796 is faulty, you can perform a continuity test using a multimeter. Follow these steps:

1. Set your multimeter to the “ohms” setting
2. Disconnect the wires from the heating element terminals
3. Place one probe of the multimeter on one terminal of the heating element and the other probe on the other terminal
4. If the multimeter reading shows continuity (a low resistance), the heating element is functioning correctly
5. If there is no continuity (infinite resistance), this indicates a faulty heating element that needs to be replaced
6. Make sure to double-check the readings to ensure an accurate diagnosis

Replacing the heating element if it is defective

If you have determined that the heating element in your Kenmore Dryer Model 796 is defective, you will need to replace it. Here’s a guide on how to do it:

1. Disconnect the wires from the heating element terminals
2. Remove the mounting screws or nuts that secure the heating element
3. Take note of the orientation of the old element before removing it
4. Insert the new heating element and secure it with the mounting screws or nuts
5. Reconnect the wires to the appropriate terminals, ensuring they are firmly attached
6. Carefully reassemble the front panel, top panel, lint trap housing, and lint filter
7. Plug in your dryer or turn on its power source
8. Perform a test run to confirm that the new heating element is working properly

By following these steps, you can diagnose and fix a faulty heating element in your Kenmore Dryer Model 796. Remember to exercise caution when working with electrical components and always ensure the dryer is unplugged or its power source is turned off before making any repairs.

Troubleshooting The Igniter And Gas Valve In Kenmore Dryer 796 Model

Is your Kenmore Dryer Model 796 not heating? Are you tired of damp clothes and endless drying cycles? The culprit might be a faulty igniter or gas valve. In this guide, we will walk you through the process of troubleshooting these components to get your dryer back to optimal performance.

---

Inspecting the igniter for visible damage

One of the first steps in troubleshooting the igniter is to visually inspect it for any signs of damage. Follow these easy steps:

1. Disconnect the dryer from the power supply.
2. Locate the igniter, typically found near the burner assembly.
3. Take a close look at the igniter for any visible cracks, breaks, or discoloration.
4. If you notice any damage, it is likely that the igniter needs to be replaced.

---

Testing the igniter for continuity with a multimeter

If the igniter appears to be in good condition, the next step is to test it for continuity using a multimeter. Follow these steps:

1. Disconnect the dryer from the power supply.
2. Remove the igniter from the dryer (refer to the manufacturer’s instructions if needed).
3. Set your multimeter to the continuity testing mode.
4. Touch one probe to each of the igniter’s terminals.
5. If the multimeter shows a reading of continuity, the igniter is functional. If there is no continuity, it means that the igniter is defective and needs to be replaced.

---

Examining the gas valve coils for proper functioning

If the igniter passes the continuity test, it is time to examine the gas valve coils. These coils are responsible for regulating the flow of gas into the dryer. Follow these steps:

1. Disconnect the dryer from the power supply.
2. Locate the gas valve coils, typically found near the gas valve assembly.
3. Visually inspect the coils for any signs of damage or wear.
4. If the coils appear to be damaged, they need to be replaced.

---

Replacing the igniter or gas valve if needed

If you have determined that either the igniter or gas valve coils are defective, it is time to replace the faulty component. It is recommended to consult the manufacturer’s instructions or seek professional assistance for this process to ensure proper installation.

Remember, troubleshooting and repairing your Kenmore Dryer Model 796 can save you both time and money. By following these steps to address issues with the igniter and gas valve, you can get your dryer up and running efficiently once again.

Other Potential Causes For Lack Of Heat In Kenmore Dryer 796 Model

When your Kenmore Dryer Model 796 is not heating, it can be frustrating and inconvenient. While a clogged vent or exhaust system is often the main culprit, there are several other potential causes that could be preventing your dryer from producing heat. In this section, we will explore these other possible culprits and how they can be addressed.

Clogged vent or exhaust system

A clogged vent or exhaust system is a common issue that can cause a lack of heat in your Kenmore Dryer Model 796. When the vent or exhaust system becomes blocked with lint or debris, it restricts the airflow and prevents the dryer from heating up properly. Cleaning the vent and exhaust system is a relatively simple fix that can be done by following these steps:

1. Unplug your dryer from the power source.
2. Disconnect the dryer from the vent or exhaust system.
3. Inspect the vent and exhaust system for any signs of blockage or buildup.
4. Remove any lint or debris using a brush or vacuum cleaner.
5. Reconnect the dryer to the vent or exhaust system.
6. Plug the dryer back into the power source.

Faulty thermostat or thermal cutoff fuse

A faulty thermostat or thermal cutoff fuse can also be a potential cause for the lack of heat in your Kenmore Dryer Model 796. These components are responsible for regulating the temperature inside the dryer. If they are not functioning properly, it can result in the dryer not heating up or overheating. Replacing these parts may be required to resolve the issue. It is recommended to consult the dryer’s user manual or seek professional assistance to ensure proper replacement.

Electrical issues or control board problems

Electrical issues or problems with the control board can also prevent your Kenmore Dryer Model 796 from producing heat. These issues can include a faulty power cord, a blown fuse in the circuit breaker, or a malfunctioning control board. To address these problems, you should check the power supply to the dryer, inspect the power cord and circuit breaker, and consider contacting a professional for further diagnosis and repair.

Professional repair options for Kenmore Dryer 796 model

If you have tried the above troubleshooting steps and are still experiencing a lack of heat in your Kenmore Dryer Model 796, it may be time to seek professional repair options. A professional technician with expertise in dryer repairs will be able to diagnose the specific issue and recommend the necessary repairs. This can save you time and ensure that the problem is resolved correctly.

Frequently Asked Questions On Kenmore Dryer Model 796 Not Heating

Conclusion

If your Kenmore Dryer Model 796 is not heating, don’t panic. This blog post has covered all the possible causes and troubleshooting techniques to help you resolve this issue. By following the steps outlined, you can identify the problem and take appropriate actions to get your dryer back to optimal performance.

Remember, regular maintenance and proper usage are key to extending the lifespan of your dryer.