Kenmore Elite HE5 dryer not heating is a common issue and can occur due to a faulty heating element or thermal fuse. To fix the problem, check these two components and replace them if found defective.
Kenmore Elite HE5 dryer not heating is a frustrating problem that can cause inconvenience and delay in your daily chores. Fortunately, it is a common issue with a straightforward solution. The dryer not heating can be caused by a faulty heating element or thermal fuse, which prevents the dryer from generating heat.
It is essential to troubleshoot the problem and replace the faulty components to get the dryer working correctly. We will guide you through the process of diagnosing and fixing the Kenmore Elite HE5 dryer not heating issue, so you can get back to your laundry as soon as possible.
Credit: m.youtube.com
Common Causes Of A Kenmore Elite He5 Dryer Not Heating
A dryer not heating up can be a frustrating issue, and it can happen to any brand or model. One such example is the Kenmore Elite He5 dryer, which is known for its efficiency and high performance. However, even the best machines can experience issues, and there could be several reasons why your Kenmore Elite He5 dryer is failing to heat up. In this section, we will discuss the most common causes of a Kenmore Elite He5 dryer not heating up, and what you can do to fix it.
Faulty Heating Element
The heating element is responsible for generating heat inside the dryer drum. It is a coil of wire that heats up when the dryer is turned on, and produces the warm air that dries your clothes. Over time, the heating element can wear out or become damaged, resulting in a lack of heat inside the dryer. If this is the case, you will need to replace the heating element to restore heat to your Kenmore Elite He5 dryer.
Faulty Thermal Fuse
The thermal fuse is a safety device that is designed to prevent the dryer from overheating. If the thermal fuse is faulty or has blown out, the dryer will not heat up. The thermal fuse is usually located on the blower housing or the heating element housing, and can be tested using a multimeter. If you find that the thermal fuse is defective, you will need to replace it before your Kenmore Elite He5 dryer can start heating up again.
Faulty Thermostat
The thermostat is another crucial component of the dryer that regulates the temperature inside the drum. If the thermostat is faulty or has malfunctioned, it can cause the dryer to stop heating. The thermostat is located either on the blower housing or the heater housing, and can be tested using a multimeter. If the thermostat is not working properly, it will need to be replaced to restore heat to your Kenmore Elite He5 dryer.
Faulty Igniter
The igniter is responsible for lighting up the gas that is used to heat up the dryer. If the igniter is faulty, it will not light up the gas, resulting in a lack of heat inside the dryer. The igniter can be checked using a multimeter to determine if it is working as expected. If it is not working, then you will need to replace the igniter to restore heat to your Kenmore Elite He5 dryer.
Faulty Gas Valve Coils
The gas valve coils are responsible for controlling the flow of gas inside the dryer. If the gas valve coils are faulty or have become worn out, they will not be able to control the flow of gas, resulting in a lack of heat inside the dryer. The gas valve coils can also be checked using a multimeter to determine if they are working properly. If not, you will need to replace them to restore heat to your Kenmore Elite He5 dryer.
Overall, there are several reasons why your Kenmore Elite He5 dryer may not be heating up, but the most common ones are a faulty heating element, thermal fuse, thermostat, igniter, and gas valve coils. By identifying the root cause of the problem, you can repair your dryer and have it back up and running in no time.
Credit: www.ebay.com
How To Diagnose The Issue
When your Kenmore Elite He5 dryer suddenly stops heating, and you are left with damp clothes, this can be incredibly frustrating. However, before you call a technician, you can run some basic checks to diagnose the problem and potentially save yourself time and money. Here, we’ll guide you through the different steps to diagnose the issue, including checking for a faulty heating element, thermal fuse, thermostat, igniter, and gas valve coils.
Check For Faulty Heating Element
A heating element that is not working as expected can be the culprit behind a dryer not heating. Kenmore Elite He5 dryers have a heating element that is located at the back of the drum. To check if the heating element is working correctly, follow these steps:
- Unplug the dryer from the wall outlet.
- Locate the heating element at the back of the dryer.
- Using a multimeter, check the heating element for continuity.
- If the multimeter reads zero, your heating element is faulty and needs to be replaced.
Check For Faulty Thermal Fuse
A thermal fuse that is not functioning correctly can cause the dryer to stop heating. The thermal fuse is a safety device that prevents the dryer from overheating. To check if the thermal fuse is the issue, follow these steps:
- Unplug the dryer from the wall outlet.
- Locate the thermal fuse at the back of the dryer, near the heating element.
- Use a multimeter to check the thermal fuse for continuity.
- If the multimeter reads zero, your thermal fuse is faulty and needs to be replaced.
Check For Faulty Thermostat
The thermostat in your dryer regulates the temperature. If your thermostat is faulty, it may not be properly regulating the temperature, causing your dryer to stop heating. To check if the thermostat is the issue, follow these steps:
- Unplug the dryer from the wall outlet.
- Locate the thermostat in the dryer.
- Use a multimeter to check the thermostat for continuity.
- If the multimeter reads zero, your thermostat is faulty and needs to be replaced.
Check For Faulty Igniter
The igniter ignites the gas that heats the dryer. If the igniter is faulty, it may not be igniting the gas, causing your dryer to stop heating. To check if the igniter is the issue, follow these steps:
- Unplug the dryer from the wall outlet.
- Locate the igniter in the dryer, near the gas valve.
- Use a multimeter to check the igniter for continuity.
- If the multimeter reads zero, your igniter is faulty and needs to be replaced.
Check For Faulty Gas Valve Coils
The gas valve coils in your dryer control the flow of gas to the burner. Faulty gas valve coils can result in the dryer not heating. To check if the gas valve coils are the issue, follow these steps:
- Unplug the dryer from the wall outlet.
- Locate the gas valve coils at the top of the gas valve.
- Use a multimeter to test the gas valve coils for continuity.
- If the multimeter reads zero, your gas valve coils are faulty and need to be replaced.
By following these steps, you can quickly diagnose the issue with your Kenmore Elite He5 dryer and take the necessary action to get it working correctly again. However, if you are not confident with fixing your dryer yourself, it is always best to get in touch with a professional technician who can help you with the repair process.
Tools You Will Need For Repairing
For repairing a Kenmore Elite He5 dryer not heating, you will need certain essential tools like a multimeter, screwdriver, flashlight, and dryer heating element coil kit. These tools will help diagnose and fix the issue efficiently, ensuring your dryer works smoothly and efficiently again.
Tools You Will Need for Repairing A Kenmore Elite He5 dryer not heating can be frustrating, especially when you have a mountain of laundry to do. However, repairing the dryer is not always a daunting task, and with the right tools, you can do it yourself. Here are the tools you will need to repair your Kenmore Elite He5 dryer. Screwdriver A screwdriver is a must-have tool for repairing a Kenmore Elite He5 dryer not heating. You will use it to remove the screws that hold the dryer panels together. It is recommended to have both a flathead and Phillips screwdriver to ensure that you have the right tool for the job. Multimeter A multimeter is a tool that measures electrical currents, voltage, and resistance. It helps diagnose the electrical issues with your Kenmore Elite He5 dryer. It enables you to check the dryer’s heating element, fuses, and thermostats to determine if there is an electrical malfunction. With the multimeter, you can accurately measure your dryer’s electric outputs and take necessary steps to fix the issue. Pliers Pliers are an essential tool for holding or twisting objects. You will use pliers to remove wires, crimp, and strip them. Additionally, you might need them to remove clamps or rings during the repair process. Wire Strippers Wire strippers are used to strip off insulation from wires. They come handy when you need to put new wires in the dryer. You will find different wire-stripping gauges, and choosing the right size depends on the wire size you need to strip. Replacement Parts Lastly, you need to have the replacement parts you need to repair your Kenmore Elite He5 dryer. You can order the heating element, fuses, and thermostats online or from your local hardware store. Ensure that you have all the necessary parts before you start repairing your dryer. In conclusion, the tools you need to repair your Kenmore Elite He5 dryer not heating consist of a screwdriver, multimeter, pliers, wire strippers, and replacement parts. With all these tools in hand and the right instructions, you can repair your dryer in no time.How To Replace Heating Element
The Kenmore Elite HE5 dryer not heating can be a frustrating issue, but replacing the heating element is a common fix. First, unplug the dryer and remove the back panel, then locate and remove the old heating element and install the new one carefully, following the manufacturer’s instructions.
Unplug The Dryer
To replace the heating element on your Kenmore Elite He5 dryer, start by unplugging the dryer from the power source. Safety always comes first, and this step will help to minimize chances of electric shock.
Remove The Back Panel
After unplugging the dryer, the next step is to carefully remove the dryer’s back panel. You will need a screwdriver or nut driver to accomplish this step. Ensure that you keep all screws safely as you will need them during reassembly.
Locate The Heating Element
Once you have removed the back panel, the heating element will now be visible. It is normally located on the right side of the dryer. Take note of how the heating element is installed and connected to the dryer before disconnecting it.
Disconnect The Heating Element
You will now need to remove the wires connected to the old heating element. Use a pair of pliers to pull off the wire connections gently. Be very careful not to damage any other parts or wires while removing the heating element and the wires connected to it.
Install The New Heating Element
With the old heating element and wires disconnected, it is now time to install the new heating element. Place it exactly where the old one was and connect the wires in a similar manner. Follow the instructions in the user manual for continuity with the dryer’s circuit.
Reattach The Back Panel
The final step is to reattach the back panel of the dryer using the screws that you removed earlier. Ensure that each screw is tightened well enough to hold the panel in place. Plug the dryer back in and test its heating function to confirm that the new heating element is installed correctly.
Replacing the heating element in your Kenmore Elite He5 dryer is not a complicated process, but you must follow these steps carefully to avoid damaging your dryer or causing electric shock. Consult the user manual for further details on handling the heating element and other parts of the dryer.
How To Replace Thermal Fuse
If your Kenmore Elite He5 dryer is not heating, it may be due to a faulty thermal fuse. To replace it, you will need to first unplug the dryer and locate the thermal fuse, which is usually near the blower wheel housing.
Then, remove the old fuse and replace it with a new one before reconnecting the wires and putting the dryer back together.
If your Kenmore Elite He5 dryer is not heating, there could be many reasons behind it. One of the most common causes is a faulty thermal fuse. A thermal fuse is a safety device that protects your dryer from overheating. When it blows, the dryer will stop heating. In this section, we will guide you on how to replace the thermal fuse on your Kenmore Elite He5 dryer, step-by-step.Unplug The Dryer
The first step is to unplug the dryer from the main socket to avoid any electrical hazards.Remove The Back Panel
Remove the screws from the back panel of the dryer using a screwdriver. Gently pull the panel towards you.Locate The Thermal Fuse
The thermal fuse is a small rectangular device with two wires attached to it. It is located on the blower housing cover. Check your dryer’s manual if you have difficulty finding it.Disconnect The Thermal Fuse
Gently remove the wires from the thermal fuse. Do not pull the wires or use excessive force as you may damage the wires.Install The New Thermal Fuse
Install the new thermal fuse in the same location as the old one. Reconnect the wires to the new thermal fuse. Make sure that the wires are properly connected and there are no loose connections.Reattach The Back Panel
Reattach the back panel to the dryer and secure it with the screws you removed previously. In conclusion, replacing the thermal fuse on your Kenmore Elite He5 dryer may look overwhelming, but it’s actually quite simple with the right tools and this step-by-step guide. Just be cautious, and you’ll have your dryer heating again in no time.How To Replace Thermostat
To replace the thermostat on a Kenmore Elite He5 dryer when it’s not heating, first unplug the dryer and locate the thermostat. Remove the wires, screws and thermostat, replace with a new one, and reassemble. Test it to ensure it’s working properly.
Unplug The Dryer
Before attempting to replace the thermostat, make sure your Kenmore Elite He5 dryer is unplugged from the electrical outlet. Safety should always come first, and electricity and metal appliances don’t mix well. Once you have the power disconnected, you are ready to proceed to the next step.Remove The Back Panel
The next step is to remove the back panel of your dryer. You can do this by using a screwdriver or another tool that will help you to remove the screws. Once the screws are removed, carefully slide the back panel off the dryer.Locate The Thermostat
The next step is to locate the thermostat in your Kenmore Elite He5 dryer. The thermostat is a small device that monitors the temperature inside the dryer and ensures that it doesn’t get too hot. It is usually located near the heating element of the dryer.Disconnect The Thermostat
Once you have located the thermostat, you need to disconnect it from the dryer. The thermostat is connected to the dryer with wires, and you’ll need to detach these wires carefully. Make sure you remember how to reconnect the wires later on.Install The New Thermostat
Now it’s time to install the new thermostat. You can purchase a replacement thermostat from an appliance parts store or online. Simply connect the wires of the new thermostat to the same places where the old thermostat was connected.Reattach The Back Panel
Finally, with the new thermostat installed, you can reattach the back panel of the dryer. Secure the screws back into place, and ensure that they are tightened properly. Once you have done that, plug in your Kenmore Elite He5 dryer and test it out again. In conclusion, replacing the thermostat in your Kenmore Elite He5 dryer is not a difficult task. With a little bit of patience and care, you can do it yourself and save yourself from calling a professional technician. Just remember to follow the steps outlined in this article, and you should have a dryer that heats up perfectly fine again in no time.How To Replace Igniter
If your Kenmore Elite HE5 dryer is not heating up, then it may be time to replace the igniter. Igniters are responsible for heating up the dryer by igniting the gas as it flows through the burner. In this post, we’ll guide you through the steps to replace the igniter in your Kenmore Elite HE5 dryer.
Unplug The Dryer
The first step in replacing the igniter is to unplug the dryer from the power source.
Remove The Front Panel
The next step is to remove the front panel of the dryer. Depending on the model of your Kenmore dryer, you may need to remove screws or clips to do this.
Locate The Igniter
After you’ve removed the front panel, you should be able to locate the igniter. The igniter is typically located near the burner assembly and is connected to the wiring harness.
Disconnect The Igniter
The next step is to disconnect the old igniter from the wiring harness. You may need to use pliers or another tool to do this.
Install The New Igniter
Once you’ve disconnected the old igniter, it’s time to install the new igniter. Insert the new igniter into the same location as the old one and reconnect it to the wiring harness.
Reattach The Front Panel
Finally, reattach the front panel of the dryer, making sure all the screws or clips are in place. Once you’ve reattached the front panel, plug the dryer back in and test to see if it’s working properly.
Credit: www.amazon.com
How To Replace Gas Valve Coils
To replace gas valve coils on a Kenmore Elite He5 dryer not heating, begin by unplugging the dryer and accessing the valve coils. Use a multimeter to test the coils for continuity and replace them if necessary. Reassemble the dryer and test it to ensure it is heating properly.
Kenmore Elite He5 dryer not heating up can be frustrating. However, if you notice that your dryer does not produce heat or takes too long to dry clothes, then it is time to take action. Fortunately, a simple repair, such as replacing the gas valve coils, can fix this problem. In this section, we will guide you through the process of replacing the gas valve coils.Unplug The Dryer
The first step is to unplug the dryer from its electrical source. This will ensure your safety during the repair process. It is also essential to turn off the gas supply to the dryer to avoid any potential gas leaks.Remove The Front Panel
Next, you need to remove the front panel of the dryer. You can do this by using a putty knife to press on the two spring clips located between the front panel and the top of the dryer. Once the clips are disengaged, lift the front panel and carefully unplug the wiring harness.Locate The Gas Valve Coils
After removing the front panel, you will see the gas valve coils. They are located on the top of the gas valve assembly, near the burner tube. To identify them, look for two black cylinder-shaped coils with wires attached to them.Disconnect The Gas Valve Coils
Using a pair of pliers, carefully disconnect the two wire connectors from the gas valve coils. Remember to grip the connectors and not the wires to avoid accidental breaks. Next, detach the mounting bracket that holds the coils in place by removing the two screws.Install The New Gas Valve Coils
Once you have removed the old gas valve coils, it is time to install the new ones. First, slide the new coils into the mounting bracket and secure them in place using the screws. Then, reattach the wire connectors to the new coils.Reattach The Front Panel
The final step is to reattach the front panel of the dryer. Place the front panel back into the slots at the bottom of the dryer and gently push down until the clips snap back into place. Finally, plug the wiring harness back in. In conclusion, replacing the gas valve coils can be an easy solution to fix your Kenmore Elite He5 dryer not heating issue. Ensure to unplug the dryer before starting the repair process, follow each step carefully, and you will be able to get your dryer up and running in no time.Conclusion
Based on our findings, the Kenmore Elite He5 Dryer not heating issue is a common problem that can be solved effectively with a few troubleshooting steps. From checking the power supply to examining the heating element, it’s important to take a systematic approach to resolve the problem.
If you’re not comfortable handling electrical components, it’s advisable to seek professional help. Remember, prompt action can save you time and money in the long run. Happy drying!